worm reduction
Our regular 700 Series – the heart of EP rate reducer products – has been serving industry reliably for over 10 years. Its proven modular style has set the sector standard for overall performance and may be the most imitated item in the current worm gear speed reducer marketplace. But why accept a knock-off when you’re able to have the original – from EP.
Specifications
11 basic single reduction sizes
8 basic double reduction sizes
1/6 – 25 HP
5:1 – 100:1 ratios single reduction
100:1 – 3600:1 ratios double reduction
Non-flanged, NEMA C-face quill, and coupled input styles
Projecting and hollow result shafts
Projecting diameters from 1/2″ to 2-1/4″
Hollow output bore diameters from 5/8″ to 3-7/16″ (with over 20 bore sizes in stock)
Product Features
The 700 Series’ large oil reservoir provides efficient heat dissipation and lubrication for much longer operating life.
Its multi-position mounting versatility permits installation in virtually any position.
Housings are straddle-milled, top and bottom level, for precise alignment of horizontal and vertical bases.
Internal baffles assure confident, leak-free venting.
The 700 Series’ rugged casing, fabricated of fine-grained, gear-quality cast iron, provides maximum strength for optimum durability, in addition to greater precision during worm and gear alignment.
EP 700 Series high-strength bronze worm gear is straddle mounted somewhere between heavy-duty tapered roller bearings to improve thrust and overhung load capacities, sizes 713-760.
Our 700 Series’ high-strength steel output shaft assures convenience of high torque and overhung loads.
Pipe plugs allow easy fill, level, and drain in virtually any mounting position.
The 700 Series’ super-finished oil-seal diameters on both input and output shafts extend seal lifestyle.
Both 2D and 3D CAD drawings can be found in our eCatalog.
EP worm gearboxes possess earned a status to be a business benchmark worldwide. Our achievement came from our relentless drive for quality with state-of-the-artwork technology, all while offering worm gearboxes happen to be affordable prices. High versatility accorded through a wide choice of mounting choices, shaft configurations and motor interfaces, would make the EP worm gearbox the default decision for the industry. The helical-worm and the double-worm version, with or without the torque limiter, soon add up to the advantage, creating an extremely versatile drive system.
EP Worm gearboxes provide large torque with low quickness gear ratio. Being basic and compact in design, these gears can perform higher gear ratio compared to the helical gears. These worm reduction gears having screw type characteristics are similar to helical gears, but its helix position is typically comparatively bigger) and its body is generally quite long in the axial direction. The gears in these gearboxes can be right or left-handed dependant on the purpose.
Mounting option include universal housing, part flanges, foot (horizontal and vertical), shaft mounted with torque arm. Available in Solid shafts (solitary or dual), with torque arm or torque limiter.
Worm reduction gears features
Principles
A worm gear is a kind of interlocking gear composed of a good worm shaft and worm wheel. The worm is definitely shaped just like a screw and the worm wheel is a kind of gear machined to have a tooth account with the same configuration.
The operation of a worm gear is comparable with that of a bolt and nut. The principle is equivalent to a nut that is fixed to ensure that it cannot rotate and therefore progresses in the axial direction when the bolt is definitely turned.
The design of a worm gear is considered through the relationship between your rack and spur gear on the middle plane of the worm wheel.
Features
Large reduction ratio One rotation of the worm rotates the worm wheel simply by one tooth. Because of this, in a 1 speed reduction gears, the wheel can be manufactured thus that it will be rotated 1/60 (1/120 in special applications).
Orthogonal shaft The shafts are aligned orthogonally due to the structure. This characteristic can help you layout the turning tranny direction at a right angle.
The arbitrariness of the rotation direction The screw direction of the worm can be clockwise or counterclockwise (generally clockwise). You’ll be able to switch the rotation direction of the worm wheel by changing the screw path.
A multitude of shaft layouts The wide variety of shaft layouts is one of the top features of interlocking gears.For example, right shaft output, remaining shaft output, dual shaft input and dual shaft output, etc., incorporate for a complete of 14 types (Physique 2) and, if attachment orientations are included, you’ll be able to select from over 40 layouts.
Low noise, low vibration The interlocking of the worm and worm wheel is certainly characteristic because the contact can be linear and the relative slide is great. In comparison with rolling power transmission, noise and vibration are really low. For this reason, this technology can be used to drive medical products, elevators and escalators, etc.
The principal specifications of worm reduction gears
MA Series(Small)
Center distance(mm) 32,40
Reduction ratio 10,20,30,40,50,60
Input capacity(kW) 0.1～1(at an input of 1800 rpm)
Output torque(N・m) 20～66
Input speed(rpm) 0～1800
MA Series(Medium)
Center distance(mm) 50,63,80,100,125,140,160
Reduction ratio 10,15,20,25,30,40,50,60
Input capacity(kW) 0.4～30(at an input of 1800 rpm)
Output torque(N・m) 900～3570
Input speed(rpm) 0～1800
S Series
Center distance(mm) 50,60,70,80,100,120,135,155,175,200,225,250,300,350,400,450,500
Reduction ratio 10,15,20,25,30,40,50,60
Input capacity(kW) 0.3～255(at an input of 1800 rpm)
Output torque(N・m) 50～56600
Input speed(rpm) 0～1800
Key points when choosing a worm reduction gears
Selection
When choosing a worm reduction gears, the procedures for selecting the right gear are described in the manufacturer catalogs and the series and models ought to be selected according to those procedures. Particular care ought to be taken in essential areas such as for example selecting the load index, calculating the overhang load and examining the heat rated potential from the manufacturer.
Cautions during use
When utilizing a worm decrease gears, heat produced during the initial period of use is large and running-in procedure at 1/4, 1/2 and 3/4 of rated torque for eight hour periods is key to sufficiently achieving the performance of the worm reduction gears.
Maintenance and inspection
After completing running-in procedure (approximately 50 hours), it is necessary to change the lubricating oil and also to change the lubricating oil from then on about 1 time per year according to the operation manual presented by the manufacturer.
Product Description
The Worm Reduction Gear Box is supplied by our company is of supreme quality. Our products are created by using premium quality materials and progress technology at our vendors end. They are widely used in various sectors. Our goods are often available at a very low market prices.
Motor Mount Frame Options
TEC Motors, worm decrease gearbox.
Option A good-160 B5 Framework, Flange Mount.
Choice B-132 B14 Frame, Face Mount.
Option C-100/112 B5 Frame, Flange Mount.
High efficiency and safe operation. High load capability and overload functions. Result Torque = (Electric power (kW) x 9550 (Regular))/ Gearbox output speed (rpm).
Higher ratios on request dependent on service factor (40:1, 50:1, 60:1, 80:1, 100:1)
DESCRIPTION
Wormgears of the VF series are actually milestones for the sector worldwide. They succeeded in merging uncompromising top quality with stateoftheart technology amd renown price effectiveness.Absolute versatility is distributed by the wide choice of several installation options, shaft configurations and motor interface, all offered as standard. The helicalworm and the doubleworm version, with or without the torque limiter, also add up, creating an extremely versatile drive system.
ADDITIONAL INFORMATION
AMP
0.42 A
EFFICIENCY 
84%
HP
0.12
KW
0.09
RATIO
7
RPM
200
TEMPERATURE RATING
20 level C TO 80 degree C
TORQUE
4 Nm
HSN
8483.40.00
WARRANTY PERIOD
12 Months
The worm reduction gears come in two series: X and H.
The series X, featuring a worm and worm wheel set, comes in versions XA with shaft and XF-XC with mounting provisions for motor.
Version XF (bell housing + coupling) provides great versatility to suit a broad selection of applications and higher efficiency than the compact range XC, where the emphasis is on space performance.
Series H supplies the same features since series X with an extra plus: a spur equipment pre-stage at the insight end provides higher overall performance and a good broader range of ratios compared to the X series.
Framework sizes 110 and 90 include a cast-iron casing cast enbloc, whereas smaller sizes make use of die-cast aluminium housings. The worm shaft is produced from casehardened and hardened alloy steel and ground-finished.
The worm wheel includes a cast iron hub with cast bronze insert. Hollow output shaft is supplied as standard.
Broad range of possibilities:
second input, result flange, single or double extension result shaft, torque limiter with through cable connection, torque arm.
